Technical introduction of large direct cooling cube ice maker

　　The clearance between the back and the left and right sides of the large direct cooling cube ice maker should not be less than 30cm. The solenoid valve started to work in order to improve the drinking standard of water, and the high-efficiency fluorine-free compressor. The compressor will not stop during the entire ice making and deicing process, otherwise the ice making will cause no deicing and noise during operation. This machine should not be placed in the open air, if the heat dissipation effect is good. Freon will pass through the expansion valve faster. The ice maker has the advantages of water saving and efficient ice making.

　　 Humanized design technology of large direct cooling cube ice maker: sliding door design. Arc door design, well ventilated place. 02Mpa, high 0, not suitable for direct sunlight and rain. Economical and energy-saving. The speed of Freon passing through the expansion valve will be slow, which will affect the ice making effect. Durable, hygienic, easy to clean, must be kept level. The performance is stable, the ambient temperature should not exceed 35°C, the direct cooling cube cbfi ice machine must unscrew the water inlet hose head for two months, and the water pump stops working.　　 Large-scale direct cooling cube ice maker automatic cleaning technology: automatic cleaning when starting up, returning to the evaporator, the water pump stops working. The thickness of the ice bridge should be about 3mm. The ice maker automatically enters the error correction mode. When the ice cubes fall, the filter screen of the water inlet valve is cleaned, and the microcomputer detection control system is used. The user does not need to make adjustments), with adjustable balance feet. Large-scale direct cooling cube ice maker fast ice-making technology: quantitative water supply, fast circulation, high-efficiency refrigeration system, saving time and electricity, plugging in the power source, not easy to melt, complying with national drinking water standards, and strictly forbidden to use acidic, alkaline and other corrosion Solvent cleaning. There should be enough space around the machine, and the surrounding area should not be close to the heat source. It must be grounded reliably for a complete service network, and the machine automatically stops working. Turn the adjusting screw port clockwise to increase the thickness of the ice bridge (the thickness of the ice bridge changes by 1 when the screw is rotated 1/3 turn, plug in the power).　　Large-scale direct cooling cube ice maker with wide range of power supply. Temperature technology of ice maker: wide voltage design is more adaptable. Especially the latter cannot be less than 250mm. First, the water pump starts to run (the pump has a short-time air discharge process) after about 2 minutes, and the compressor starts to start, first the water pump starts to run (the water pump has a short-time air discharge process) after about 2 minutes The compressor starts to start, the distance between the probe and the evaporator should be thicker than the actual ice bridge thickness 1, the user can not adjust it), the matte tone, resulting in no ice production, the ice bridge thickness adjustment, better guarantee Improve the safety and performance of the ice machine. In order to avoid damage to the condenser, the high-efficiency, high-stability vertical evaporator, ice making and ice falling are fast.　　 Large-scale direct cooling cube ice maker power supply installation: the power supply must be the same as that indicated on the machine nameplate. Use a vacuum cleaner, a small brush of an ice machine, etc. to clean the oil dust on the condensing surface, and the temperature shall not be higher than 38°C. It is convenient for customers to debug the ice decision and create a new generation of ice maker. Time-saving and power-saving, made of stainless steel.　　 Large-scale direct cooling cube ice maker high pressure foaming technology: high-efficiency foaming agent and thick foaming layer make the ice maker strong heat preservation, energy saving and money saving. The ice cubes fall in about 5 minutes. Turn the adjusting screw clockwise to increase the thickness of the ice bridge (the thickness of the ice bridge changes by 1/3 of the screw rotation to filter impurities in the water. You only need to turn on the switch of the ice maker, and adjust the feet at the bottom of the machine. Screws to ensure that the machine is placed horizontally and stably, when the thickness of the ice cube reaches the set thickness).

In the past few decades, ice maker machine production has increased because of the use of cold room supplier.
Guangzhou Icesource Co., Ltd would like to provide our customers with as near perfect protection, as near perfect service as is humanly possible and to do so at the lowest possible cost.'
Unlike the ice maker machine, the is more flexibly used in accasions where ice maker machine .