Snow ice machine maintenance tips [selected]

Snowflake cbfi ice machine uses a refrigeration system, using a water carrier to pass through a certain device under power, and the device that produces ice is called an ice maker. The ice maker is a kind of refrigeration mechanical equipment that produces ice after the water passes through the evaporator and is cooled by the refrigeration system refrigerant.

　　Cleaning and maintenance: the content of the maintenance cycle. The method does not exceed 15 days. Air filter cleaning. Soak the filter in a neutral detergent solution, clean it with a soft brush, and install it after drying. No more than three months for surface cleaning. Use a cloth dipped in neutral detergent to wipe the water. Clean the system according to the relevant instructions in the 'Cleaning Operation Procedure'. Remove the water system components for no more than six months for cleaning and disinfection; for cleaning and disinfection of the refrigerator, press 'Operation procedures for removing parts for cleaning (or disinfection)' instructions for condenser cleaning. For dust, compressed air can be used to blow from the top to the bottom; for oil, you can use a commercial coil cleaner to clean. Check whether the circuit wiring is loose, tighten or plug in the wiring.

　　 1. Cleaning procedure (1) When the ice harvesting process is over and the ice cubes fall off the evaporating tray, turn the function switch to the 'stop' position; (2) Take out the ice cubes in the refrigerator; 　　(3) Turn the switch to the 'cleaning' position, start the cleaning or disinfection process, and start to pour water into the sink.　　(4) When the water pump is running, the water flows out from the water distribution pipe, and after flowing through the evaporation pan, add an appropriate amount of detergent to the water tank.　　(5) The ice maker automatically completes the cleaning process and automatically rinses the machine.　　(6) After cleaning is completed, the ice maker enters the standby state. At this time, turn the function off to the 'ice making' position, and the ice maker will start making ice. 2. Operation procedures for removing parts for cleaning (or disinfection): 　　 (1) Turn off the water source of the ice maker and cut off the power supply of the ice maker; 　　 (2) Remove the water curtain plate, water distribution pipe and other parts that need to be cleaned (or disinfected) ;　　(3) Soak the removed parts in an appropriate amount of cleaning (or disinfecting) solution. The ratio of the solution is shown in the following table: Solution category Water cleaning/disinfectant dosage cleaning solution 1 gallon (4 liters) 16 ounces (500 ml) ) Disinfecting solution 4 gallons (15 liters) 3 ounces (90 ml) 　　 (4) Clean the parts carefully with a soft bristle brush or sponge (do not use a metal brush); 　　 (5) Clean the top of the evaporator protrusion with a solution and a brush, Side and bottom; 　　 (6) Thoroughly rinse all cleaned (or disinfected) parts with clean water; 2.7 Install and remove parts; 2.8 Turn on the water source and power supply. 3. Precautions for cleaning (or disinfection): 　　 (1) When using ice machine cleaners and disinfectants, please wear rubber gloves and protective goggles, and it is recommended to wear a face mask; 　　 (2) Only use cleaners and disinfectants; The part number of the cleaning agent is 9405463 and the color is blue; the part number of the disinfectant is 9405653 and the color is pink. Please provide the part number when ordering; 　　(4) Cleaning and disinfection should be carried out separately, first cleaning, then disinfection. Do not mix cleaning agents and disinfectants; 　　 (5) After adding cleaning agents or disinfectants, the cleaning (or disinfection) process cannot be manually interrupted, otherwise there will be cleaning agents or disinfectants remaining in the machine.

are present in just about every facet of modern life.
Looking for someone to handle your cold room supplier ice maker machine needs? Check out Icesource today for more information.
Guangzhou Icesource Co., Ltd believes that the shorter the path between consumer and product, the more likely businesses are to convert more sales.
Now that Guangzhou Icesource Co., Ltd has become a leader in the space and have been able to scale appropriately, we are ready to expand to other cities.
It's not enough to have an idea as cold room supplier in a gigantic market. The key to what gets concerned is how you connect this hungry market to the idea that satisfies it.