Energy saving refrigeration solution supplier since 2004.                                                                                                                                                                                                                                                                                                   

Language

Analysis of the use process of the snowflake ice maker

2021/12/05
What is the general process of the snowflake ice machine in use? Let’s take a look at the following:      1. Start the Snowflake , turn on the water, and place it at the main power switch (connected). The Snowflake starts to work: the machine is delayed, that is, after three minutes, restart the power to decelerate The device, compressor, and other components indicate the high temperature condensation red light (LED) flashing during this period (i.e. a delay of 3 minutes). About three minutes after the ice on the first field of snow, the compressor activated the reserve refrigerator, and the ice was normal after 10 minutes, resulting in hard ice.    Second, the snowflake ice machine stops and the main power switch is turned off, and the machine stops working. Every time you turn on the machine, the machine must be delayed for 3 minutes before running automatically. 3. Description of the ice machine index The front panel of the electronic snowflake ice machine to monitor the five lights as follows:    green on; machine power status yellow light on; storage refrigerator ice period, 10 seconds after the ice is deleted, the machine will automatically resume working yellow The light is on; the fish tank is water. When the water is in the water for 10 seconds, the machine will automatically resume working. The red light is on; the condenser temperature, the ambient temperature is too high or too low, the red light is on, and the red light is on for 3 minutes. The drilling speed is lower than the error or change 850.rPm   the high evaporator temperature with red light flashing: that is, the non-evaporating temperature is lower than -1℃ after 10 minutes;   Note: 1. The reason for the high condenser temperature: the fan cannot Normal work; Condenser plug-in; Condensation PC board temperature sensor or too high ambient temperature can cause damage.   2. Reasons for high evaporation temperature: lack of refrigerant; condensation temperature is too high; evaporation temperature sensor or PC board is damaged. Fourth, Snow is reset (reset). When the machine stops working due to the safety device when activated, such as restarting the machine, first determine the cause of the fault and troubleshooting, and then press the reset button (reset) or the main power switch Turn off (disconnect) and then place it in the upper position (connected) position. Use and maintenance of      Snowflake      Snowflake must be installed in a well-ventilated place, and the ambient temperature should not exceed 35°C to prevent excessively high ambient temperature from causing poor condenser heat dissipation and affecting the ice making effect. The ground on which the ice maker is installed should be firm and level, and the ice maker must be level to avoid causing no ice removal and noise during operation.     Snowflake ice maker must regularly unscrew the head of the water inlet hose and clean the water inlet valve filter thoroughly to prevent sand and mud impurities in the water from clogging the water inlet, causing the water inlet to become smaller and making ice impossible. The clearance between the back and the left and right sides of the ice maker is not less than 30cm, and the clearance between the top is not less than 60cm. The cbfi ice machine uses an independent power supply, a dedicated line power supply, is equipped with a fuse and a leakage protection switch, and must be reliably grounded.     When cleaning the Snowflake , turn off the power. It is strictly forbidden to flush the machine directly with the water pipe. Use neutral detergent for scrubbing, and it is strictly forbidden to clean with acidic, alkaline and other corrosive solvents. When the cbfi ice machine is not in use, clean it, use a hair dryer to dry the ice mold and the moisture in the box, and place it in a ventilated and dry place. Avoid storing in the open air or direct sunlight. The sink, water pipe, refrigerator and protective film of the ice maker should be cleaned at intervals.
If you have a need for ice maker machine cold room supplier, like , and , you need to be able to find a dependable provider who you can trust when necessary.
To discover more about the ice maker machine benefits of , go to Icesource .
The global market is estimated to reach a value of almost ice maker machine in the next decade. have a robust position in the ice maker machine market because of its proven high potency in ice maker machine.
CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
العربية
English
Español
français
Polski
Português
русский
Türkçe
Current language:English