Energy saving refrigeration solution supplier since 2004.                                                                                                                                                                                                                                                                                                   

Language

About the importance of cleaning and maintenance of ice machines

2022/02/16

Many people will ask a question: Why is the cleaning of the ice machine important?

Because the ice machine is in contact with water for 24 hours, there are small impurities and microbes in the tap water, and the ice cubes are directly put in the beverage. Therefore, the maintenance and cleaning of the ice machine is very traditional Chinese medicine, which not only improves the service life of the machine, but also guarantees the quality of the product.

What will happen if the ice machine is not cleaned daily?

If the machine is not cleaned for a long time, a large number of bacteria will grow in the ice tray, sink, and internal grooves of the ice machine.

How to maintain the ice machine on a daily basis

Scrub the appearance of the machine (the ice machine with heat dissipation louvers, use a brush to clean the vent)

Check the filter element (shops without whole house water purification, Replace the filter element once per week)

Check if there are any residual solid particles in the corners of the sink (for cleaning)

What do you need to do to clean the ice maker

1. When the ambient temperature drops When the temperature is below 0°C, there is a possibility of freezing. Drainage work must be performed to drain the water, otherwise it may cause the water inlet pipe to rupture!

2. When the cbfi ice machine is not in use, it should be cleaned, and the ice mold and moisture in the box should be blown dry with a hair dryer. It should be placed in a non-corrosive gas and ventilated and dry place. Avoid storing in the open air.

3. The surrounding environment of the ice maker should be cleaned regularly, and no debris should be piled up to hinder heat dissipation.

4. The ice maker should be installed in a place far away from heat sources, no direct sun exposure, and well-ventilated. The ambient temperature should not exceed 35°C to prevent the condenser from causing poor heat dissipation due to excessive ambient temperature. Ice making effect. The ground on which the ice maker is installed should be firm and level, and the cbfi ice machine must be level, otherwise it will cause no ice removal and noise during operation.

5. The clearance between the back and the left and right sides of the ice maker is not less than 30cm, and the top clearance is not less than 60cm.

6. The ice maker must be installed on a solid ground, and the machine must be installed horizontally without tilting. Otherwise, the machine will vibrate, and if the tilt is too large, it will store water in the refrigerator, which will affect the quality of the ice.

7. The water pipe, sink, refrigerator and protective film of the ice maker should be cleaned every two months.

8, the ice maker should use an independent power supply, dedicated line power supply, equipped with fuse and leakage protection switch, and reliable grounding.

9. The water used by the cbfi ice machine must meet the national drinking water standards, and a water filter device should be installed to filter impurities in the water to avoid clogging the water pipe and polluting the water tank and ice mold. And affect the ice making performance.

10. Turn off the power when cleaning the ice machine. It is strictly forbidden to flush the machine directly with the water pipe, use neutral detergent to scrub, and it is strictly forbidden to clean it with acidic, alkaline and other corrosive solvents.

11. The ice maker must unscrew the head of the water inlet hose for two months to clean the water inlet valve filter screen to avoid sand and mud impurities in the water from blocking the water inlet, causing the water inlet to become smaller, leading to failure Ice making.

12. The ice maker must clean the surface of the condenser every two months. Poor condensation and heat dissipation will cause damage to the compressor components. When cleaning, use a vacuum cleaner, a small brush, etc. to clean the oil and dust on the condensing surface. Do not use sharp metal tools to clean, so as not to damage the condenser.


Guangzhou Icesource Co., Ltd also discusses implications for both research and the practice of operations in building systems to help people succeed in both the short and long run.
If you have any issues with your cold room supplier, you will have to call the experts at Icesource to assist you. Any of your enquiry is warmly welcomed.
Getting cold room supplier from an idea to production is a complex process. It involves significant research, time, planning and patience. But with the right information, the right resources and the right product, it's possible.
cold room supplier provider at Icesource offers a wide variety of in many options. quality is absolutely ensured if you choose us. welcome to visit our factory.
CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
العربية
English
Español
français
Polski
Português
русский
Türkçe
Current language:English